Audio Setup Guide

Connect Your Audio

EveryTongue works with any sound setup, from a phone in your pocket to a professional mixing console. Ministers across the globe, evangelists on the road, pastors in every nation, no longer limited by one language. Just put your phone in front and preach. Your words stream into any language, in real time.

Get StartedFind My Board

Two Ways to Connect

Pick whichever works best for your church. Both deliver real-time sermon translation to your congregation.

Recommended

Option A: Phone or Tablet

This is how we want every minister on the planet using EveryTongue. Evangelists, traveling preachers, missionaries, pastors in villages with no sound system. Just put your phone in front and preach. Your words stream into any language, in real time. No infrastructure required.

No cables, no adapters, no sound system needed

Works anywhere on earth with an internet connection

Set up in under one minute. Preach in every language.

Best for

Everyone. Ministers across the globe, evangelists on the road, churches of any size, missionaries in the field. Translation for all, regardless of infrastructure.

Advanced

Option B: Audio Board

Connect your mixing console's USB or auxiliary output to a laptop, then open the Host Dashboard. Direct audio from the board delivers the best possible quality.

Best audio quality for accurate translation

No background noise or room echo

Isolate the pastor's mic from the worship band

Best for

Established churches with a permanent location and existing sound system. Studio-quality audio fed directly into the translation engine for maximum accuracy.

Pro Tip - Wear a Headset for the Best Results

If you are using Option A (phone or tablet), one small change makes a huge difference: have the pastor or speaker wear a single AirPod, earbud, or any headset with a built-in microphone. This keeps the mic just inches from their mouth instead of feet away on the pulpit, dramatically reducing background noise and echo. The result is clearer audio and more accurate translations for your congregation.

Apple AirPods or AirPods Pro

Samsung Galaxy Buds

Any Bluetooth headset with a mic

Wired earbuds with an inline mic

The speaker only needs one ear in - they can still hear the room naturally with the other. Pair the headset to the phone or tablet running the Host Dashboard and the device will automatically use the headset's microphone. No extra hardware, no extra cost - just a simple upgrade that makes EveryTongue work even better.

Audio Board Guides

Step-by-step instructions for the most popular church mixing consoles. Find your board below.

Showing 19 of 19 boards

Budget

$200 - $800 - Small Churches

The most popular digital mixers in small churches. These X32 variants all share the same X32 architecture with USB audio recording built in.

Available Outputs

USB (32x32 channels)AUX Send (6.35mm TRS)Ultranet

Step-by-Step Connection

  1. 1

    Connect a USB cable from the X32 Rack/Compact/Producer to your laptop.

  2. 2

    The X32 appears as a multi-channel USB audio device. No driver is needed on macOS; on Windows, install the free Behringer USB driver from behringer.com.

  3. 3

    On the mixer, press SETUP > CONFIG/ROUTING > CARD OUTPUT. Set Card outputs 1-2 to the Main L/R bus (this sends the main mix over USB).

  4. 4

    Open your web browser to everytongue.church and go to your Host Dashboard.

  5. 5

    Click the microphone/audio input selector and choose 'X32' or 'USB Audio Device' from the dropdown.

  6. 6

    Speak into the pulpit microphone and confirm the audio meter is showing signal on the Host Dashboard.

Pro Tips

  • Use the USB connection for the cleanest digital signal path -- no analog conversion needed.

  • If you only want the pastor's microphone (not the full mix), route only that channel to a dedicated bus and assign that bus to the Card output.

  • Keep the USB cable under 5 meters, or use a powered USB hub for longer runs.

Compact, rack-mountable digital mixers controlled entirely via tablet or laptop. The XR18 includes an 18-channel USB audio interface.

Available Outputs

USB (18x18 channels on XR18)AUX Send (6.35mm TRS)Headphone Out

Step-by-Step Connection

  1. 1

    Connect a USB cable from the XR18 to your laptop. (XR16 and XR12 use the AUX or headphone output instead.)

  2. 2

    On macOS, the XR18 is recognized automatically. On Windows, install the ASIO driver from behringer.com.

  3. 3

    Using the X Air Edit app, go to SETUP > ROUTING and confirm the USB sends are set to Main L/R on channels 1-2.

  4. 4

    Open everytongue.church on your laptop and navigate to your Host Dashboard.

  5. 5

    Select the XR18 USB device as your audio input.

  6. 6

    Test by speaking into a connected microphone and watch for audio levels on the dashboard.

Pro Tips

  • For XR16/XR12 (no USB audio): run a 3.5mm-to-6.35mm cable from the AUX output into your laptop's microphone input, or use a simple USB audio adapter.

  • The XR18 can also stream audio over WiFi via its built-in router, but a wired USB connection is far more reliable for translation.

  • Position the XR unit in the sound booth for the shortest USB cable run.

Yamaha's workhorse analog mixers with built-in USB audio interfaces. The 'XU' suffix means USB is included. Extremely common in smaller worship settings.

Available Outputs

USB (2-channel stereo)AUX Send (6.35mm TRS)Monitor Out

Step-by-Step Connection

  1. 1

    Connect a USB cable from the MG mixer's USB port to your laptop.

  2. 2

    Install the Yamaha Steinberg USB Driver if prompted (available at yamaha.com/downloads).

  3. 3

    The USB output mirrors the stereo bus by default -- whatever you hear in the main speakers goes over USB.

  4. 4

    Open everytongue.church on your laptop and go to your Host Dashboard.

  5. 5

    Select 'Yamaha MG' or 'USB Audio' as the audio input device.

  6. 6

    Verify signal by speaking into a mic and checking the dashboard audio meter.

Pro Tips

  • The USB output level follows the main stereo fader. Set your main fader to a healthy level (around 0 dB).

  • If you only need the spoken-word mic and not the full worship band mix, use the AUX send instead and route only the pastor's channel to it.

  • These mixers are class-compliant on macOS -- no driver installation needed.

Compact analog mixers with USB recording output. Known for warm, musical preamps. Popular with churches that value audio quality on a budget.

Available Outputs

USB (2-channel stereo)AUX Send (6.35mm TRS)ALT OUT

Step-by-Step Connection

  1. 1

    Connect the ZED's USB port to your laptop using a standard USB cable.

  2. 2

    On the ZED-10FX/ZED-14, the USB output is hardwired to the main mix bus -- no routing setup needed.

  3. 3

    Ensure the USB/PLAYBACK knob on the mixer (if present) is set so the USB SEND is active.

  4. 4

    Open everytongue.church on your laptop, go to the Host Dashboard.

  5. 5

    Select 'USB Audio' from the audio input dropdown.

  6. 6

    Do a quick mic check to confirm audio is flowing.

Pro Tips

  • Allen & Heath ZED mixers are class-compliant USB devices. No driver needed on macOS or modern Windows.

  • Use the ALT OUT as a secondary send if you want to keep USB for recording and send a separate feed to EveryTongue via a USB audio adapter.

  • The ZED preamps are exceptionally clean -- keep gain staging moderate for the best speech intelligibility.

Mackie's latest generation analog mixers with built-in USB-C audio interfaces. Excellent value with Onyx preamps and a 2x4 USB interface.

Available Outputs

USB-C (2x4 channels)AUX Send (6.35mm TRS)Control Room Out

Step-by-Step Connection

  1. 1

    Connect the ProFX to your laptop using the included USB-C cable (or USB-C to USB-A adapter).

  2. 2

    The ProFX v3 series is class-compliant -- it appears as a standard audio device immediately.

  3. 3

    The USB output sends the main stereo mix by default. Use the 'USB SEND SOURCE' switch on the mixer to choose between main mix or a dedicated channel.

  4. 4

    Open everytongue.church and navigate to the Host Dashboard.

  5. 5

    Select 'Mackie ProFX' from the audio input selector.

  6. 6

    Speak into the pulpit mic and confirm the signal on the Host Dashboard.

Pro Tips

  • Use the 'USB SEND SOURCE' switch to send only the pastor's channel if you don't want background music in the translation.

  • The v3 series works at up to 24-bit/192kHz, but EveryTongue works fine at the default 48kHz. No need to change sample rates.

  • If using USB-C to USB-A, ensure you use a data-capable cable, not a charge-only cable.

Compact Soundcraft mixers with built-in USB audio interfaces. The Notepad-12FX is one of the most affordable USB mixers available. The Signature 12 adds more channels and Lexicon effects.

Available Outputs

USB (2-channel stereo)AUX Send (6.35mm TRS)

Step-by-Step Connection

  1. 1

    Connect the Soundcraft mixer to your laptop via USB.

  2. 2

    Install the Soundcraft USB Audio driver if prompted (available at soundcraft.com).

  3. 3

    The USB output on the Notepad-12FX is fixed to the main stereo mix. On the Signature 12, it follows the main output.

  4. 4

    Open everytongue.church and go to the Host Dashboard on your laptop.

  5. 5

    Select the Soundcraft device from the audio input dropdown.

  6. 6

    Speak into a connected microphone and verify the audio meter responds.

Pro Tips

  • The Notepad-12FX works well at 48kHz. Avoid changing sample rates in your operating system settings.

  • For speech-only translation, use the AUX send to isolate just the vocal microphone. Connect the AUX output to a USB audio adapter plugged into your laptop.

  • Keep the Soundcraft's USB connection direct -- avoid USB hubs when possible for lowest latency.

Mid-Range

$800 - $5,000 - Medium Churches

The full-size X32 with motorized faders and the headless X32 Core. Both offer the same 32x32 USB audio interface and full routing flexibility.

Available Outputs

USB (32x32 channels)AUX SendUltranetAES50

Step-by-Step Connection

  1. 1

    Connect a USB cable from the X32's rear USB port to your laptop.

  2. 2

    On the X32, go to SETUP > CONFIG > ROUTING tab. Under CARD OUTPUT, set outputs 1-2 to Main L/R.

  3. 3

    On Windows, install the X32 USB driver. On macOS, no driver is needed.

  4. 4

    Open everytongue.church on your laptop and navigate to the Host Dashboard.

  5. 5

    Select 'X32' or 'USB Audio' as the input device.

  6. 6

    Run a sound check by speaking into the pulpit mic. Confirm levels on the dashboard.

Pro Tips

  • The X32 Core is headless (no faders/screen). Use the X32 Edit software on a laptop or the X32-Mix app on a tablet to access routing.

  • For the cleanest speech feed, create a dedicated mix bus with only the spoken-word microphone and route that bus to the USB Card outputs.

  • The X32 can simultaneously send USB audio and run AES50 to stage boxes -- USB recording doesn't interfere with live sound.

Yamaha's TouchFlow digital mixers with intuitive touchscreen operation. The Tio1608-D stage box connects via Dante. USB recording is built in via the Tio rack or a NY64-D card.

Available Outputs

USB (via Tio1608-D)OMNI OUT (6.35mm TRS)Dante Network Audio

Step-by-Step Connection

  1. 1

    Option A (USB via Tio): Connect a USB cable from the Tio1608-D stage box to your laptop. The Tio acts as the USB audio interface.

  2. 2

    Option B (OMNI OUT): On the TF, assign an OMNI OUT to carry the main L/R bus. Run a cable from that output to a USB audio adapter on your laptop.

  3. 3

    On the TF, press SETUP > OUTPUT PATCH and confirm the OMNI OUT or Tio USB sends are sourced from the Stereo bus or a dedicated mix bus.

  4. 4

    Open everytongue.church on your laptop, go to the Host Dashboard.

  5. 5

    Select the USB audio device from the input dropdown.

  6. 6

    Speak into the pastor's mic and verify the audio meter on the dashboard.

Pro Tips

  • The TF series supports 'one-touch' GainFinder -- use it to set optimal mic gain for the spoken word channel.

  • If your church uses Dante networking, you can use Dante Via or Dante Virtual Soundcard on the laptop to receive audio directly over Ethernet -- no analog cables needed.

  • The TF's built-in recorder can record to USB simultaneously with sending audio to EveryTongue.

Allen & Heath's SQ series -- powerful 48-channel digital mixers with built-in 32x32 USB audio and a 96kHz processing engine. Popular upgrade path for growing churches.

Available Outputs

USB (32x32 channels)Local Outputs (XLR/TRS)SLink (digital snake)

Step-by-Step Connection

  1. 1

    Connect a USB-B cable from the SQ mixer to your laptop.

  2. 2

    On the SQ, go to I/O PATCH > USB AUDIO. Set USB Send 1-2 to Main L/R (or a dedicated mix bus for speech only).

  3. 3

    On Windows, install the Allen & Heath USB driver from allen-heath.com. On macOS, the SQ is class-compliant.

  4. 4

    Open everytongue.church on your laptop and navigate to the Host Dashboard.

  5. 5

    Select 'Allen & Heath SQ' from the audio input selector.

  6. 6

    Perform a mic check and verify levels on the dashboard.

Pro Tips

  • The SQ runs at 96kHz natively. Your OS may show it as a 96kHz device. This is fine -- EveryTongue handles sample rate conversion automatically.

  • Use a dedicated mix bus (e.g., Mix 11-12) with only the pastor's mic to isolate speech from the worship band.

  • The SQ's built-in DEEP compressor presets include a 'Speech' setting that helps even out vocal dynamics for better translation accuracy.

Midas M32 is the premium sibling of the Behringer X32, featuring Midas PRO preamps and build quality. The M32R is the rack-mount version. Both share the X32 architecture with 32x32 USB audio.

Available Outputs

USB (32x32 channels)AUX SendAES50Ultranet

Step-by-Step Connection

  1. 1

    Connect a USB cable from the M32/M32R to your laptop.

  2. 2

    On the M32, press SETUP > ROUTING > CARD OUTPUT. Assign outputs 1-2 to the Main L/R bus.

  3. 3

    On Windows, install the Midas/Behringer USB driver. macOS requires no driver.

  4. 4

    Open everytongue.church on your laptop and go to the Host Dashboard.

  5. 5

    Select 'M32' or 'USB Audio' from the audio input dropdown.

  6. 6

    Check audio levels by speaking into the pulpit microphone.

Pro Tips

  • The M32 and X32 use the same USB driver and protocol. Any X32-compatible instructions work identically on the M32.

  • Midas PRO preamps have slightly more headroom -- you can push the gain a bit higher without distortion.

  • The M32R lacks motorized faders. Use the Midas M32-Mix iPad app or M32-Edit desktop app for detailed routing.

PreSonus StudioLive Series III S mixers with AVB networking, built-in USB-C audio (up to 55x55 channels), and tight integration with Studio One DAW and UC Surface control app.

Available Outputs

USB-C (up to 55x55 channels)FlexMix Outputs (XLR)AVB Network Audio

Step-by-Step Connection

  1. 1

    Connect a USB-C cable from the StudioLive to your laptop.

  2. 2

    Install Universal Control from presonus.com if prompted. This installs the USB audio driver and UC Surface control app.

  3. 3

    In UC Surface, go to SETTINGS > STREAM ROUTING. Assign USB Send 1-2 to the Main bus.

  4. 4

    Open everytongue.church on your laptop and navigate to the Host Dashboard.

  5. 5

    Select 'PreSonus StudioLive' from the audio input dropdown.

  6. 6

    Test with a live mic to confirm audio is flowing to the dashboard.

Pro Tips

  • The StudioLive can send up to 55 channels over USB. Only channels 1-2 (Main L/R) are needed for EveryTongue.

  • Use a FlexMix as a dedicated speech-only bus and route it to a USB send for the cleanest translation feed.

  • AVB networking can send audio over Ethernet if your laptop supports AVB. This avoids running long USB cables from the stage to the sound booth.

A powerful 32-channel touchscreen digital mixer from QSC. Features multi-track USB recording, built-in effects, and anti-feedback. No USB audio streaming -- uses a recording drive approach.

Available Outputs

USB Recording (to external drive)AUX Output (6.35mm TRS)Main Out (XLR)

Step-by-Step Connection

  1. 1

    The TouchMix-30 Pro does NOT function as a live USB audio interface. Instead, use an AUX output.

  2. 2

    On the TouchMix, configure an AUX send and assign the pastor's microphone channel to that AUX bus.

  3. 3

    Run a cable from the AUX output (6.35mm TRS) to a USB audio adapter connected to your laptop.

  4. 4

    Open everytongue.church on your laptop and go to the Host Dashboard.

  5. 5

    Select the USB audio adapter from the input dropdown.

  6. 6

    Test the audio path by speaking into the pastor's microphone.

Pro Tips

  • Since the TouchMix doesn't stream USB audio, a simple USB audio adapter (like the Behringer UCA222 at around $30) bridges the gap perfectly.

  • Use the TouchMix's 'Anti-Feedback Wizard' on the speech channel before running EveryTongue -- cleaner audio means better translation.

  • Set the AUX send to 'pre-fader' if you want the EveryTongue feed to be independent of the house mix level.

A wireless 32-channel digital mixer controlled entirely via the Mackie MasterFuse app on iPad, iPhone, or Android. Features a built-in WiFi router and 32x32 USB audio recording.

Available Outputs

USB (32x32 channels)AUX Out (6.35mm TRS)WiFi Control

Step-by-Step Connection

  1. 1

    Connect a USB cable from the DL32S to your laptop.

  2. 2

    On the MasterFuse app, go to ROUTING > USB SEND. Set USB channels 1-2 to the Main L/R mix.

  3. 3

    The DL32S is class-compliant on macOS. On Windows, install the Mackie USB driver from mackie.com.

  4. 4

    Open everytongue.church on your laptop and go to the Host Dashboard.

  5. 5

    Select 'Mackie DL32S' from the audio input selector.

  6. 6

    Perform a mic check and confirm levels.

Pro Tips

  • The DL32S has no physical controls -- all mixing is done from the app. Make sure your tablet/phone stays connected to the DL32S WiFi for control.

  • The USB connection is independent of WiFi control. Your laptop can be on a different network.

  • Use a dedicated mix bus on USB sends 3-4 for speech-only audio if you want to isolate the pastor's mic from the full band mix.

High-End

$5,000 - $50,000+ - Large Churches

Yamaha's flagship CL and QL series digital consoles with Dante networking, up to 72 input channels, and legendary Yamaha reliability. The gold standard for large worship facilities.

Available Outputs

Dante Network AudioOMNI OUT (XLR/TRS)Mini-YGDAI Expansion Slots

Step-by-Step Connection

  1. 1

    Option A (Dante): Install Dante Virtual Soundcard (DVS) from audinate.com on your laptop. Connect the laptop to the same Dante network as the CL/QL via Ethernet.

  2. 2

    In Dante Controller, route the CL/QL's Main L/R Dante outputs to your DVS inputs on the laptop.

  3. 3

    Option B (OMNI OUT): Assign an OMNI OUT on the CL/QL to the Stereo bus. Run a cable to a USB audio adapter on the laptop.

  4. 4

    Open everytongue.church on your laptop and navigate to the Host Dashboard.

  5. 5

    Select the Dante Virtual Soundcard (or USB adapter) from the audio input dropdown.

  6. 6

    Test by speaking into the pulpit mic and verifying levels on the dashboard.

Pro Tips

  • Dante gives you the cleanest, most reliable audio path. If your facility already runs Dante, always prefer this method.

  • Dante Virtual Soundcard requires a one-time license purchase from Audinate (around $30). It is worth every penny for large installations.

  • Create a dedicated MIX bus with only the spoken-word microphone for the most accurate translation. Worship music can confuse speech recognition.

DiGiCo's SD range represents world-class digital mixing. These consoles use proprietary Optocore fiber networking and support MADI, Dante, and AES outputs.

Available Outputs

MADI (coaxial/optical)Dante (via DMI card)Local Outputs (XLR)

Step-by-Step Connection

  1. 1

    Option A (Dante via DMI card): If your SD console has a DMI-Dante card installed, use Dante Virtual Soundcard on your laptop as described in the Yamaha CL/QL guide above.

  2. 2

    Option B (MADI): Use a MADI-to-USB interface (such as RME MADIface) connected to your laptop.

  3. 3

    Option C (Local XLR out): Assign a local output to the Main bus. Run an XLR cable to a USB audio adapter on the laptop.

  4. 4

    On the DiGiCo, use the OUTPUT ROUTING page to assign the desired bus to your chosen output.

  5. 5

    Open everytongue.church and go to the Host Dashboard. Select the audio device.

  6. 6

    Test with a live microphone to confirm audio flow.

Pro Tips

  • DiGiCo consoles are high-end professional gear. If your church has a DiGiCo, you likely have an audio engineer -- involve them in the setup.

  • The DMI-Dante card is the easiest path for EveryTongue integration. Most large churches with DiGiCo already have Dante infrastructure.

  • For the cleanest speech feed, create a dedicated auxiliary bus on the SD console and send only the spoken-word channels to it.

Avid's flagship live sound system used in the largest churches and touring productions. Features AVB networking, Pro Tools integration, and modular I/O via the VENUE Stage 64.

Available Outputs

AVB Network AudioMADIPro Tools RecordingAnalog/AES Direct Outs

Step-by-Step Connection

  1. 1

    Option A (AVB): Install Avid VENUE AVB drivers on your laptop. Connect to the same AVB network. Route Main L/R to AVB outputs.

  2. 2

    Option B (MADI): Use an MADI-to-USB interface (such as RME MADIface) for multi-channel recording.

  3. 3

    Option C (Direct Out): Assign a direct output or matrix output to the Main bus. Run an XLR to a USB audio adapter on your laptop.

  4. 4

    On the S6L surface, go to OUTPUTS > PATCH and assign the output to the Stereo bus or a dedicated speech matrix.

  5. 5

    Open everytongue.church and navigate to the Host Dashboard. Select the correct audio device.

  6. 6

    Perform a sound check to verify signal.

Pro Tips

  • The S6L can record up to 128 channels simultaneously. Sending 2 channels to EveryTongue will not impact console performance.

  • If your church records services with Pro Tools, you can use the same Pro Tools session to send a mix to EveryTongue via software routing (e.g., Loopback by Rogue Amoeba).

  • Dedicated matrix outputs are ideal for EveryTongue -- they let you create a custom speech-only mix independent of the main house output.

Soundcraft's Vistonics-based digital consoles with HARMAN connected ecosystem. Features MADI, Dante (via option card), and Soundcraft Realtime Rack plugin hosting.

Available Outputs

MADIDante (via option card)Local Outputs (XLR)AES3

Step-by-Step Connection

  1. 1

    Option A (Dante via option card): Install a Dante option card in the Vi. Use Dante Virtual Soundcard on your laptop to receive Main L/R.

  2. 2

    Option B (MADI): Use an RME MADIface or similar MADI-to-USB interface.

  3. 3

    Option C (Local output): Assign a local output on the Vi to the Main bus. Cable it to a USB audio adapter.

  4. 4

    On the Vi console, go to the OUTPUT PATCH page and assign the chosen output to the Stereo bus or a dedicated group.

  5. 5

    Open everytongue.church and go to the Host Dashboard.

  6. 6

    Select the appropriate audio device and verify signal.

Pro Tips

  • The Vi series supports Soundcraft Realtime Rack for UAD-powered plugins. If using vocal processing plugins, ensure they are on the speech channel before the EveryTongue send.

  • MADI gives you up to 64 channels on a single cable. Only route 2 channels (Main L/R or speech bus) for EveryTongue.

  • The Dante option card is a cost-effective upgrade if your church is moving toward IP audio networking.

Allen & Heath's flagship dLive system -- 128 input channels, 96kHz processing, XCVI FPGA engine. The C Class (C1500, C2500, C3500) and S Class (S3000, S5000, S7000) offer different form factors with the same powerful engine.

Available Outputs

Dante (via DM64 or M-DL-ADAPT)SLink (digital snake)Local Outputs (XLR)AES3

Step-by-Step Connection

  1. 1

    Option A (Dante via DM64 or adapter): Configure the DM64 Dante module or M-DL-ADAPT card. Use Dante Virtual Soundcard on your laptop.

  2. 2

    Route the Main L/R bus to a Dante send via the dLive's I/O PATCH page.

  3. 3

    Option B (Local output): Assign a local output (XLR) to the Main bus and connect to a USB audio adapter on your laptop.

  4. 4

    Open everytongue.church on your laptop and go to the Host Dashboard.

  5. 5

    Select the audio device from the input dropdown.

  6. 6

    Sound check and confirm levels on the dashboard.

Pro Tips

  • The dLive's DEEP processing plugins are excellent for vocal clarity. Apply the 'Dynamic EQ' or 'Vocal Leveller' on the pastor's channel for more consistent speech.

  • If your dLive uses SLink to connect surfaces and MixRacks, Dante is the best way to get audio out to a laptop without touching the analog outputs.

  • The dLive supports 96kHz processing. Dante Virtual Soundcard works natively at 96kHz for pristine audio quality.

Solid State Logic's Live consoles represent the pinnacle of audio quality for live sound. Used by the world's most prestigious churches and venues. Features Dante, MADI, and Blacklight II connectivity.

Available Outputs

DanteMADIBlacklight II (fiber)Local Outputs (XLR/AES)

Step-by-Step Connection

  1. 1

    Option A (Dante): The SSL Live consoles support Dante natively. Use Dante Virtual Soundcard on your laptop to receive Main L/R.

  2. 2

    On the SSL, go to PATCHBAY > DANTE and assign Main L/R to Dante outputs 1-2.

  3. 3

    Option B (Local XLR): Assign a local output to the Stereo bus and cable to a USB audio adapter.

  4. 4

    Connect your laptop to the Dante network via Ethernet or use the local output path.

  5. 5

    Open everytongue.church and go to the Host Dashboard. Select the audio input.

  6. 6

    Verify audio flow with a live microphone test.

Pro Tips

  • SSL Live consoles deliver reference-grade audio. The speech captured for EveryTongue will be exceptionally clean.

  • If your church has an SSL, you almost certainly have a dedicated audio team. They can set up a dedicated Dante send in minutes.

  • The SSL's channel EQ is outstanding for speech. A gentle high-pass filter at 100Hz and a presence boost at 3-5kHz will improve translation accuracy.

Universal Guide

Board not listed above? No problem. Any mixer with one of these outputs can work with EveryTongue.

USB Output

Connect a USB cable from your board to your laptop. The board appears as an audio device. Select it in the Host Dashboard.

Best quality - digital signal

AUX / Line Out

Run a cable from an AUX send or line output to a USB audio adapter plugged into your laptop. Adapters cost around $10-30.

Great quality - analog signal

Headphone Jack

Use a 3.5mm or 6.35mm cable from the headphone output to your laptop's mic input (with a 6.35mm-to-3.5mm adapter if needed).

Good quality - universal fallback

Need a USB Audio Adapter?

If your board has only analog outputs (no USB), you will need a simple USB audio adapter. These are small, inexpensive devices ($10-30) that plug into your laptop's USB port and accept a 3.5mm or 6.35mm audio input. Popular options include the Behringer UCA222 ($25), Focusrite Scarlett Solo ($50), and the generic USB-to-3.5mm adapters available at any electronics store.

Quick Start

From registration to live translation in four simple steps.

1

Register

Register your church at everytongue.church/register

2

Connect Audio

Use your phone's mic or connect your audio board via USB or AUX

3

Open Dashboard

Log in to your Host Dashboard and select your audio input

4

Start Session

Click “Start Session” - your congregation listens at everytongue.church/your-church

Register Your Church

Frequently Asked Questions

Common questions about connecting your audio to EveryTongue.

EveryTongue handles audio format conversion automatically. Whether your board sends 16-bit, 24-bit, 44.1kHz, 48kHz, or 96kHz audio, EveryTongue will process it correctly. You do not need to change any sample rate or bit depth settings on your mixer.

No. All you need is a modern web browser. We recommend Google Chrome for the best experience, but Firefox, Edge, and Safari also work. There is no app to install, no plugin to download, and no subscription to manage.

Yes. Both connection methods work over WiFi. Your phone or laptop just needs a stable internet connection. For Option A (phone/tablet), WiFi is the default. For Option B (audio board), you can connect your laptop to WiFi while receiving audio over USB from the mixer.

We highly recommend it when using Option A (phone or tablet). Having the pastor wear a single AirPod, earbud, or any headset with a built-in microphone keeps the mic close to their mouth instead of relying on the phone's mic from the pulpit. This dramatically reduces background noise and room echo, which means clearer audio and more accurate translations. Apple AirPods, Samsung Galaxy Buds, any Bluetooth headset with a mic, or even basic wired earbuds with an inline mic all work great. The speaker only needs one ear in so they can still hear the room naturally. Just pair the headset to the phone or tablet running the Host Dashboard -- the device will switch to the headset mic automatically.

Any mixing console with a USB output, AUX send, headphone jack, or any analog output can work with EveryTongue. See the Universal Guide section above. If you need help, contact us and we will walk you through it step by step.

No. EveryTongue receives a copy of the audio signal. It does not alter, interrupt, or interfere with your live sound in any way. USB recording outputs, AUX sends, and Dante sends are all designed to tap audio without affecting the main mix.

EveryTongue is designed for real-time translation. The total latency from spoken word to translated text on a congregant's phone is typically 2-4 seconds, depending on the length of phrases and internet speed. This is fast enough for comfortable worship.

Need Help Setting Up?

Our team is here to walk you through it. Contact us and we will help you get connected - free of charge, as always.

Register Your ChurchBack to Home
“How then shall they call on him in whom they have not believed? and how shall they believe in him of whom they have not heard?”

Romans 10:14

A Ministry of King Enterprises · Est. 1970 · Del Rio, Texas